C# Класс NewTOAPIA.Net.Rtp.RtpSession

Creates a basic RtpSender This RtpSender simply sends data over the wire. It uses the least amount of CPU and network bandwidth at the cost of reliability (i.e. it makes no attempts to improve data arrival at the remote site).

Creates an RtpSender with Forward Error Correction This RtpSender sends the data requested by the user, plus some extra data in order to help recover lost data. The recovery packets are sent per the specified ratio of cDataPx : cFecPx, e.g. 3:1 means for every 3 data packets we will send 1 fec packet. This means we can lose any 1 of the 4 packets and recover the data. 3:2 means we can lose any 2 of the 5 and still recover the data. It takes 1 FEC packet to recover 1 lost data packet. It is important to balance the extra CPU and network bandwidth against the reliability of the data. Increasing either CPU or network bandwidth too much may cause worse data loss than not correcting at all. If the FEC ratio uses only 1 FEC packet (2:1, 3:1, etc.) we use an XOR algorithm, which is very fast. If the ratio uses more than one FEC packet (3:2, 5:3, etc.), we use the Reed-Solomon algorithm. Reed-Solomon is more complicated and therefore requires more CPU, however it allows you to recover from a broader range of loss patterns.

Initialize object and performance counters, before they are actually put to usage.

The RtpSession can be in 1 of 4 states: 1. Sending/Receiving Rtp + Rtcp traffic - this is what most users want 2. Sending/Receiving Rtcp traffic - used mainly by diagnostic tools for discovery of people while also announcing the local user 3. Receiving Rtcp traffic only - a special diagnostic case used by Pipecleaner to discover if an Agent is already running. 4. Sending Rtp + Rtcp traffic - a rare case only used for sending test data or for "playback" of data in a scenario where SSRC and CNAME conflicts aren't of interest to the sender. THIS SHOULD ONLY BE USED IN EXCEPTIONAL CASES. -If no participant is provided (null), then RtpSession cannot send Rtp or Rtcp data (state 3) -Else a valid participant is provided and Rtcp traffic can be sent (states 1, 2, or 4) -If rtpTraffic is true, then Rtp traffic is sent and/or received (state 1 or 4) -If receiveData is true, then Rtp traffic is received as well as sent (state 1) -Else Rtp and Rtcp traffic are not received (state 4) -Else rtpTraffic is neither sent nor received (state 2)

Note that receiving Rtp data without sending Rtcp data is seen as a privacy concern and is not allowed.

This constructor is the same as "RtpSession(IPEndPoint multicastEP, RtpParticipant participant, bool rtpTraffic, bool receiveData)", except that it is capable of using a Unicast-Multicast reflector.

SendAppPacket is used to send application specific data to all other RtpListeners on the network.

AddOrUpdateParticipant is called by the RtpSession ctor for adding the local participant and by ProcessSdesPacket when an SDES packet arrives on the RtcpListener thread If the participant does not exist in the session, we add them If the participant does exist in the session, we make sure there is no CName conflict

Called to create a stream via Rtcp and have all the "links" created CXP always stores the Participant ssrc/SdesData first in the SdesPacket. So a participant should always exist before the stream is created in this code. AddStream is called by the RtcpListener thread via ProcessSdesPacket

Verifies that the SSRC matches the IPAddress, if this is a known SSRC, and returns the associated RtpStream. If the SSRC is new, we add the IPAddress to the lookup table.

Determine if there is a CNameConflict between the local participant and a remote participant or 2 remote participants. If the conflict involves a local participant, raise the event and then Dispose the RtpSession, bringing it back to a clean state. If it is a remote conflict, do nothing, as we will eventually receive the Rtcp data from them.

Check to see if a participant is stale (has not received Rtcp Sdes packets)

Called on the RtcpSender thread every RtcpIntervals So that the session can iterate through the streams and see if they are doing anything

Matches the signature of the WaitCallback so we can launch it from a ThreadPool thread during a CNameConflict

Dispose the Rtcp/Rtp listeners and senders Usually one would dispose items in the opposite order from which they were created in order to maintain symmetry. However, because objects are created due to data received from the network, we first shut down the Rtcp/Rtp listeners so as not to create new objects during shutdown. Since we are no longer listening on the network, we won't receive our own "dispose" messages that we send out, so we dispose the items manually using the same methods as if the data had come in off the wire. This allows for proper eventing and logging.

Initialize the Rtcp/Rtp listeners and senders. See the primary constructor's summary for an explanation of the "states" an RtpSession can be constructed in.

A ByePacket can contain multiple SSRCs so we need to process them in a loop

Converts a generic RtcpPacket into a specific RtcpPacket type and forwards it to the appropriate method to be processed

An SdesPacket can contain multiple Sdes reports (ssrc, SdesData) which we process here Due to our architecture with 1 RtpSession / RtpParticipant and multiple RtpSenders / RtpStreams (each of which get their own ssrc and SdesData) it is difficult to properly map the SdesData to the participant, because they all share the same CName. The participant properties will have a CName, Name, Email, Phone, etc plus any private extensions for the participant. In order to conserve Rtcp bandwidth, the streams will only send out CName, Name and any private extensions for the stream. And the stream's Name may be completely different from the participant's name. The problem is that we don't want the participant to be updated from the stream's properties due to sharing a CName. So we use the private extension "Source" to distinguish between a participant's SdesData and a Stream's SdesData The last complication is that AccessGrid doesn't have this private extension, probably because they have a 1:1 mapping between a sender and receiver. In order to not break interop, we allow for the case of the private extension not being there, in which case the participant data will be updated from any and all SdesData that share that CName

Removes a participant and does all the necessary cleanup of streams and associations

Called to remove an ssrc/stream and have all the links cleaned up A stream can either be "associated" (meaning it is mapped to a participant) or not. Whether the stream is associated or not, it will be added to/removed from the "streams" and "ssrcToIPAddress" collections. If the stream is "associated" it will be added to/removed from the participant's streams collection and the "ssrcToParticipant" collection.

This method is one extra layer of checks to make sure someone isn't messing with us (trying to remove streams they don't own by sending BYE packets for instance) If we know the IPAddress of the request to RemoveStream, make sure it is the same IPAddress that owns the stream

Called by RtcpSender when it is time to collect Rtcp data

Finishes the creation of an RtpSender by adding it to local collections and announcing it to the remote sites via an Rtcp packet