C# 클래스 ICSharpCode.SharpZipLib.Checksums.Adler32

Computes Adler32 checksum for a stream of data. An Adler32 checksum is not as reliable as a CRC32 checksum, but a lot faster to compute. The specification for Adler32 may be found in RFC 1950. ZLIB Compressed Data Format Specification version 3.3) From that document: "ADLER32 (Adler-32 checksum) This contains a checksum value of the uncompressed data (excluding any dictionary data) computed according to Adler-32 algorithm. This algorithm is a 32-bit extension and improvement of the Fletcher algorithm, used in the ITU-T X.224 / ISO 8073 standard. Adler-32 is composed of two sums accumulated per byte: s1 is the sum of all bytes, s2 is the sum of all s1 values. Both sums are done modulo 65521. s1 is initialized to 1, s2 to zero. The Adler-32 checksum is stored as s2*65536 + s1 in most- significant-byte first (network) order." "8.2. The Adler-32 algorithm The Adler-32 algorithm is much faster than the CRC32 algorithm yet still provides an extremely low probability of undetected errors. The modulo on unsigned long accumulators can be delayed for 5552 bytes, so the modulo operation time is negligible. If the bytes are a, b, c, the second sum is 3a + 2b + c + 3, and so is position and order sensitive, unlike the first sum, which is just a checksum. That 65521 is prime is important to avoid a possible large class of two-byte errors that leave the check unchanged. (The Fletcher checksum uses 255, which is not prime and which also makes the Fletcher check insensitive to single byte changes 0 - 255.) The sum s1 is initialized to 1 instead of zero to make the length of the sequence part of s2, so that the length does not have to be checked separately. (Any sequence of zeroes has a Fletcher checksum of zero.)"

상속: IChecksum

파일 보기 프로젝트 열기: NexusMods/NexusModManager-4.5 1 사용 예제들

공개 메소드들

메소드	설명
Adler32 ( ) : System	Creates a new instance of the Adler32 class. The checksum starts off with a value of 1.
Reset ( ) : void	Resets the Adler32 checksum to the initial value.
Update ( byte buffer ) : void	Updates the checksum with an array of bytes.
Update ( byte buffer, int offset, int count ) : void	Updates the checksum with the bytes taken from the array.
Update ( int value ) : void	Updates the checksum with a byte value.

메소드 상세

Adler32() 공개 메소드

Creates a new instance of the Adler32 class. The checksum starts off with a value of 1.

public Adler32 ( ) : System
리턴	System

Reset() 공개 메소드

Resets the Adler32 checksum to the initial value.

public Reset ( ) : void
리턴	void

Update() 공개 메소드

Updates the checksum with an array of bytes.

public Update ( byte buffer ) : void
buffer	byte	/// The source of the data to update with. ///
리턴	void

Update() 공개 메소드

Updates the checksum with the bytes taken from the array.

public Update ( byte buffer, int offset, int count ) : void
buffer	byte	/// an array of bytes ///
offset	int	/// the start of the data used for this update ///
count	int	/// the number of bytes to use for this update ///
리턴	void

Update() 공개 메소드

Updates the checksum with a byte value.

public Update ( int value ) : void
value	int	/// The data value to add. The high byte of the int is ignored. ///
리턴	void